Results 21 to 29 of 29
Thread: Throttle Body Market
-
07-22-2011, 06:35 AM #21
- Join Date
- Apr 2010
- Location
- IN
- Posts
- 2,148
lol sorry i shouldve been specific, should i cahnge out the gaskets on a used ls6 intake before i put it on?
-
07-22-2011, 01:00 PM #22
Use a small screw driver or pick to pull one out and roll it around in your fingers if its soft and flexable she's good to go if it feels dried and cracked they need to be replaced.
I am doing mine next week and I am hoping to reuse my LS1 gaskets.
Do you have new knock sensors yet?
Coolant crossover?
Rear Plugs?
-
07-23-2011, 12:44 PM #23
- Join Date
- Apr 2010
- Location
- IN
- Posts
- 2,148
I have a new coolant crossover but what about rear plugs and knock sensors??
-
07-23-2011, 01:55 PM #24
You could use a second crossover and block off the middle tube.
The GM Dealership I go to for parts said the plugs were discontinued and the tubes were $65.00 a piece.
I was going to shave the bottom of the intake and use the stock coolant lines,but as luck would have it I found the crossover and plugs as a kit from Texas Speed for $60.00.
I bought 2 new knock sensors for mine part #12589867,they have the harness in stock if mine is fubarred but I want to look at it first.2010 Camaro SIM 2SS/RS A6
1999 TA A4 NBM
12.265 at 110.52mph
-
07-23-2011, 04:35 PM #25
well i decided to pnp my tb. I started light to get a hag of it. I still have some more to do tomorrow but I got done like 75%. I also did the bump stop mod. I noticed a quicker throttle response. Not bad. my idle is slightly high but I think if i reset the pcm it might relearn it.
Last edited by JayTA98; 07-23-2011 at 04:39 PM.
-
07-24-2011, 09:39 AM #26
- Join Date
- Apr 2010
- Location
- IN
- Posts
- 2,148
so for the ls6 intae swap...what do i need?
i have the coolant crossover kit from WS6 store
can i use my ls1 rails?
and i forget what lube i need for the injector o rings and intake gaskets...
-
07-24-2011, 02:00 PM #27
you can use the rails from your ls1 intake. I didn't have to use any lube for the intake gaskets or injector o rings. you need an EGR block off plate and if you are deleting AIR the block off for that as well. Remember that some LS6 don't have hook up for EGR tube so the SES light will be on unless you tune it out. Same with the AIR stuff.
Last edited by JayTA98; 07-24-2011 at 02:02 PM.
-
07-24-2011, 07:48 PM #28
- Join Date
- Apr 2010
- Location
- IN
- Posts
- 2,148
air/erg/air pump hs been deleted long ago lol. but i remember reading that you should grease or lube the injectors and gaskets tho... i just dont remeber where
-
08-11-2011, 04:31 AM #29
- Join Date
- Aug 2011
- Location
- Browns Mills NJ
- Posts
- 190
Green- 1995 Z28 w/ LS1 Swap
PNP stocker all the way
Thread Information
Users Browsing this Thread
There are currently 1 users browsing this thread. (0 members and 1 guests)
Similar Threads
-
Throttle Body
By Firefighter78 in forum External EngineReplies: 11Last Post: 04-29-2008, 11:37 AM -
stock throttle body or after market
By mrcarter in forum External EngineReplies: 4Last Post: 01-11-2008, 05:36 PM -
pp throttle body
By blackbird99 in forum External EngineReplies: 6Last Post: 12-27-2007, 07:05 PM -
Which Throttle Body??? S3 vs. BBK
By 99blueZ in forum External EngineReplies: 19Last Post: 10-11-2006, 04:19 PM -
98-02 stock LS1 f-body throttle body
By noblesramair in forum Parts Wanted / TradeReplies: 2Last Post: 03-04-2006, 05:59 PM
Bookmarks